|
|
Printronix P5000 Printer Technical Note 5-0045 Rev A |
|
Introducing the P5000 Phase III SureStak Power Stacker |
|
Summary:
Around November 2002, a new power
stacker design was introduced with features to address
ease of use, reliability and serviceability. It is referred to
as the Phase III SureStak Power
Stacker. |
|
Resolution:
The table below identifies the problems that existed with the
Phase I and Phase II Power
Stackers and shows the enhancements that were designed into the
Phase III Power Stacker to
address these concerns.
|
Limit Switches
bend causing “chattering” |
Replaced with
Reed Switches p/n 204234-001 |
|
Timing Belt
slips |
Added Timing
Belt Tensioner p/n 173818-001 |
|
Difficult to access paper supply/stack |
Added
Thumb Switch, Paper Tray, Paper Tent |
|
Difficult access to Paper Tent handle |
Added Slide-out Tray and ”handled” Paper Tent |
|
Frame misalignment due to use/service |
Frame, Rail, Frame Bearing and Base more robust |
|
Rear Control Panel hard to service |
Control panel housing modified for easier removal |
|
Print Compression problems |
New Friction Washers and Compression Spring |
Important Note
To ensure the best print quality when using the
PIII Stacker, optimized step tables are available for CMX/CFX-based
printers.
The minimum Flash software to use is
359517-001 – LP+/PGL/VGL, V3.14F.
PPC PSA3 Printers have no minimum software
requirement.
Reference
For Complete Detailed Information on Phase I and
II Stackers including Illustrated Parts Breakdowns, please
reference 164253-001F - Maintenance Manual, P5000.
For Complete Detailed Information on Phase III
Stackers including Illustrated Parts Breakdowns, please
reference:
175455-001B - Maintenance Manual, P5/10/15
173843-001C - Maintenance Manual, P5220D/P5224D
176475-001B - Maintenance Manual, P5220S/P5X0XH (PSA3)
P5XXX SureStak Power Stacker Spares
|
Part Description |
Phase II P/N |
Phase III P/N |
| Motor (Paddle,
Elevator) |
158446-001 |
158446-001 |
| Motor, Drive
Roller |
173530-001 |
173530-001 |
| Pulley, Timing
Belt |
163992-001 |
178058-001 |
| Drive Roller
Shaft Assy |
158736-901 |
158736-901 |
| Ground Clip,
Dimpled |
174457-901 |
175726-901 |
|
Paper Motion Detector, Power Stacker
(Field Kit) |
170289-001 |
170289-001 |
| Sensor Assy,
PMD |
170295-001 |
170295-001 |
| Field Kit,
Limit Switch |
170285-001 |
N/A |
| Switch, Reed,
Limit SPST, NC |
N/A |
204234-001 |
| Timing Belt |
202716-001 |
202716-001 |
| Rear Control
Panel Assy. |
158732-901 |
174780-001 |
| Compression
Spring |
159425-001 |
176781-001 |
| Power Cable,
Power Stacker |
174414-001 |
174414-001 |
| Logic Cable,
CMX/CFX |
158444-001 |
158444-001 |
| Logic Cable,
PPC PSA3 |
N/A |
176029-001 |
| Anti-Static
Brush |
158313-001 |
158313-001 |
|
Pivot Arm Block, Power Stacker (Field Kit) |
170306-001 |
170306-001 |
| Constant Force
Spring |
202713-001 |
N/A |
| Spares Kit,
Spring, Conforce |
N/A |
178839-001 |
| Cable, Rail,
Vertical, Stacker |
158442-001 |
173823-001 |
| LED, IR, T-1,
¾ |
202727-001 |
202727-001 |
| Photo, NPN.
Rectifier |
202728-001 |
202728-001 |
| Tent, Paper,
Power Stacker |
173864-901 |
173864-901 |
| Elevator, I/O
Cable |
N/A |
174759-001 |
| Frame Cable,
Power Stacker |
158445-001 |
173824-001 |
P5XXX SureStak
Power Stacker Field Replacement or Upgrade Kits
Field Kit, Phase III Power Stacker 175273-001+
Field Kit, Full Conversion, PIII Power Stacker
(PSA3) 177273-001*
+This kit is to be used for replacing or
upgrading existing stacker printers to Phase III.
*This kit includes threaded inserts, a rear door
and all cabling for CMX, CFX and PPC-based printers for
conversion from a non-stacker printer into a stacker
printer Used also to replace an existing Phase I/II Stacker into
a Phase III Stacker. Flash software and additional memory are
not included in either kit. |
|
|
Need help? Call our
knowledgeable sales staff at:
1-800-243-3338
|
|
